1.概述

systemd-networkd 是一個管理網絡服務程序，可以用來管理以太網，WIFI，網橋，EC20 等模塊的網絡優先級，以及連接情況。配合 systemd-resolved 服務一起使用。

本章主要目的是學習以太網，wifi，EC20 模塊同時管理，并按指定優先級收發數據。

2.硬件資源

? MYD-YA15XC-T 開發板

? WIFI 天線

? USB 轉接板

? EC20 模塊

? 網線

? 路由器

3. 軟件資源

? Linux kernel 5.4.31

? systemd-networkd

? systemd-resolved

4.環境準備

將 MYD-YA15XC-T 燒入鏡像，wifi 天線連接 WIFI， EC20 模塊接入 USB 口，接入網線，路由器配置 wifi 熱點，并連接外網。

5.操作步驟

5.1.檢查環境

1) 檢查 systemd-networkd 運行狀態。

root@myir:~# systemctl status systemd-networkd

[[0;1;32m●[[0m systemd-networkd.service - Network Service

Loaded: loaded (/lib/systemd/system/systemd-networkd.service; enabled; vend

or preset:

Active: active (running)[[0m since Fri 2020-04-10 18:39:40 UTC; 40min ago

2) 檢查 systemd-resolved 運行狀態。

root@myir:~# systemctl status systemd-resolved

systemd-resolved.service - Network Name Resolution

Loaded: loaded (/lib/systemd/system/systemd-resolved.service; enabled; vendor

preset: enabled):40:02 myir systemd-networkd[205]: usb0: Configured

Active: active (running)[[0m since Fri 2020-04-10 18:39:41 UTC; 42min ago

?Active: active(running) 正在運行

3) 查看 DNS 配置文件

root@myir:~# ls -l /etc/resolv.conf

lrwxrwxrwx 1 root root 24 Mar 9 2018 /etc/resolv.conf -> /etc/resolv-conf.system

d

root@myir:~# ls -l /sbin/resolvconf

lrwxrwxrwx 1 root root 21 Mar 9 2018 /sbin/resolvconf -> ../usr/bin/resolvectl

root@myir:~# ls -l /usr/bin/resolvectl -rwxr-xr-x 1 root root 79316 Mar 9 2018 /usr/bin/resolvectl

?resolv.conf 是 resolv-conf.systemd 的軟連接

?/sbin/resolvconf 是/usr/bin/resolvectl 軟連接

4) 查看網絡管理信息

root@myir:~# networkctl

IDX LINK TYPE OPERATIONAL SETUP

1 lo loopback carrier unmanaged

2 can0 n/a off unmanaged

3 eth0 ether routable configured

4 wlan0 wlan off unmanaged

5 usb0 gadget no-carrier configured

5 links listed. ?lo 本地回環 沒有在 systemd 上管理

?eth0 以太網 已經在 systemd 上管理

?wlan0 wifi 沒有在 systemd 上管理

注意：如果是開發板是 STM32MP151 系列處理器則沒有 can 網絡。

5.2 檢查 xx-xxx.network

Systemd-networkd 的設備寫法為 xx-xxxx.network。 必須以 network 結尾，前面遍歷會以字典順序執行。 可以將設備配置文件放置這幾個目錄 /etc/systemd/network/ ,/run/systemd/network/ , /lib/systemd/network/. 優先級為 /etc/ > /run/ > /lib/ 。在 5.1 中已經知道以太網被管理，這里直接從它的配置文件入手。 新建文件

/lib/systemd/network/50-wired.network

[Match]

Name=eth*

[Network]

DHCP=ipv4

[DHCP]

RouteMetric=15

CriticalConnection=true

?Name=eth* 所有 eth 開頭設備適配下面方案

? HDCP=ipv4 自動獲取 IP

? RouteMetric 躍點數 15

躍點數 ip route 可以看到如下信息：

root@myir:/etc/ppp/peers# ip route

default via 192.168.30.1 dev eth0 proto dhcp src 192.168.30.103 metric 15

192.168.7.0/24 dev usb0 proto kernel scope link src 192.168.7.2 linkdown

192.168.30.0/24 dev eth0 proto kernel scope link src 192.168.30.103

192.168.30.1 dev eth0 proto dhcp scope link src 192.168.30.103 metric 15

?Metric 15 路由躍點數 15

注：躍點數能夠反映躍點的數量、路徑的速度、路徑可靠性、路徑吞吐量以及管理屬性，Metric 的值越小，優先級越高。

5.3 開啟 wifi 并檢查網絡現象

1) 使用 wpa_supplicant 命令連接 wifi。

root@myir:~# ifconfig wlan0 up

root@myir:~# wpa_passphrase SSID passwd >> /etc/wpa_supplicant.conf

root@myir:/# wpa_supplicant -B -iwlan0 -c /etc/wpa_supplicant.conf

Successfully initialized wpa_supplicant

root@myir:/# ls[ 8972.189374] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link b

ecomes ready

root@myir:/# udhcpc -i wlan0

udhcpc: started, v1.31.1

udhcpc: sending discover

udhcpc: sending discover

udhcpc: sending select for 192.168.43.185

udhcpc: lease of 192.168.43.185 obtained, lease time 3600

/etc/udhcpc.d/50default: Adding DNS 192.168.43.1

2) 查看 ip address 情況

root@myir:/# ip address

1: lo: mtu 65536 qdisc noqueue state UNKNOWN gr,up,lower_up>

oup default qlen 1000

link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00

inet 127.0.0.1/8 scope host lo

valid_lft forever preferred_lft forever

inet6 ::1/128 scope host

valid_lft forever preferred_lft forever

2: can0: mtu 16 qdisc noop state DOWN group default qlen 10,echo>

link/can

3: eth0: mtu 1500 qdisc mq state UP g,multicast,up,lower_up>

roup default qlen 1000

link/ether e2:2d:77:f3:19:23 brd ff:ff:ff:ff:ff:ff

inet 192.168.30.102/24 brd 192.168.30.255 scope global dynamic eth0

valid_lft 7194sec preferred_lft 7194sec

inet6 fe80::e02d:77ff:fef3:1923/64 scope link

valid_lft forever preferred_lft forever

4: wlan0: mtu 1500 qdisc fq_codel stat,multicast,up,lower_up>

e UP group default qlen 1000

link/ether b0:02:47:59:f5:e5 brd ff:ff:ff:ff:ff:ff

inet 192.168.43.185/24 brd 192.168.43.255 scope global wlan0

valid_lft forever preferred_lft forever

inet6 2408:84f3:2c41:7bb:b202:47ff:fe59:f5e5/64 scope global dynamic mngtmp

addr

valid_lft 3388sec preferred_lft 3388sec

inet6 fe80::b202:47ff:fe59:f5e5/64 scope link

valid_lft forever preferred_lft forever

5: usb0: mtu 1500 qdisc fq_codel sta,broadcast,multicast,up>

te DOWN group default qlen 1000

link/ether d6:b0:42:8d:a4:08 brd ff:ff:ff:ff:ff:ff

inet 192.168.7.2/24 brd 192.168.7.255 scope global usb0

valid_lft forever preferred_lft forever

?eth0 ip 192.168.30.102

?wlan0 ip 192.168.43.185

3) 再次查看 ip route 情況。

root@myir:/etc/ppp/peers# ip route

default via 192.168.30.1 dev eth0 proto dhcp src 192.168.30.103 metric 15

192.168.7.0/24 dev usb0 proto kernel scope link src 192.168.7.2 linkdown

192.168.30.0/24 dev eth0 proto kernel scope link src 192.168.30.103

192.168.30.1 dev eth0 proto dhcp scope link src 192.168.30.103 metric 15

192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.185

4) 查看 networkctl 情況。

root@myir:~# networkctl

IDXLINK TYPE OPERATIONAL SETUP

1 lo loopback carrier unmanaged

2 can0 can off unmanaged

3 eth0 ether routable configured

4 wlan0 wlan routable unmanaged

5 usb0 gadget no-carrier configuring

5 links listed. ?wlan 已經開啟，但是沒有被管理

5) 再次查看路由情況。

root@myir:/# cat /etc/resolv.conf

# This file is managed by man:systemd-resolved(8). Do not edit. #

# This is a dynamic resolv.conf file for connecting local clients directly to

# all known uplink DNS servers. This file lists all configured search domains. #

# Third party programs must not access this file directly, but only through the

# symlink at /etc/resolv.conf. To manage man:resolv.conf(5) in a different way, # replace this symlink by a static file or a different symlink. #

# See man:systemd-resolved.service(8) for details about the supported modes of

# operation for /etc/resolv.conf. nameserver 192.168.1.1

nameserver 192.168.43.1

? 192.168.43.1 為 wlan0 新增

6) 根據以上情況，可以得出，訪問外網時，只有 eth0 可以工作，wlan0 無法工作。

root@myir:~# ping www.baidu.com -I eth0

PING www.a.shifen.com (14.215.177.38) from 192.168.30.103 eth0: 56(84) bytes of

data. 64 bytes from 14.215.177.38 (14.215.177.38): icmp_seq=1 ttl=55 time=7.68 ms

64 bytes from 14.215.177.38 (14.215.177.38): icmp_seq=2 ttl=55 time=6.82 ms

64 bytes from 14.215.177.38 (14.215.177.38): icmp_seq=3 ttl=55 time=7.15 ms

64 bytes from 14.215.177.38 (14.215.177.38): icmp_seq=4 ttl=55 time=7.09 ms

64 bytes from 14.215.177.38 (14.215.177.38): icmp_seq=5 ttl=55 time=7.13 ms

^C

--- www.a.shifen.com ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4005ms

rtt min/avg/max/mdev = 6.819/7.174/7.677/0.278 ms

? wlan0 無法連接外網。

root@myir:~# ping www.baidu.com -I wlan0

PING www.a.shifen.com (14.215.177.38) from 192.168.43.185 wlan0: 56(84) bytes o

f data. ? 測試拔掉網線后情況。

root@myir:~# ip route

192.168.7.0/24 dev usb0 proto kernel scope link src 192.168.7.2 linkdown

192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.185

root@myir:~# networkctl

IDX LINK TYPE OPERATIONAL SETUP

1 lo loopback carrier unmanaged

2 can0 can off unmanaged

3 eth0 ether no-carrier configured

4 wlan0 wlan routable unmanaged

5 usb0 gadget no-carrier configuring

5 links listed. root@myir:~# cat /etc/resolv.conf

# This file is managed by man:systemd-resolved(8). Do not edit. #

# This is a dynamic resolv.conf file for connecting local clients directly to

# all known uplink DNS servers. This file lists all configured search domains. #

# Third party programs must not access this file directly, but only through the

# symlink at /etc/resolv.conf. To manage man:resolv.conf(5) in a different way, # replace this symlink by a static file or a different symlink. #

# See man:systemd-resolved.service(8) for details about the supported modes of

# operation for /etc/resolv.conf. nameserver 192.168.43.1

7) 根據以上的現象 unmanaged 與沒有路由表。還是無法使用 wlan0 接口連通外網。

root@myir:~# ping www.baidu.com -I wlan0

PING www.a.shifen.com (163.177.151.110) from 192.168.43.185 wlan0: 56(84) byte

s of data. ^C

--- www.a.shifen.com ping statistics --- 5 packets transmitted, 0 received, 100% packet loss, time 4177ms

? 但當使用手動給 wlan0 增加一條路由表后如下。

root@myir:~# ip route add default via 192.168.43.1 dev wlan0

root@myir:~# ip route

default via 192.168.43.1 dev wlan0

192.168.7.0/24 dev usb0 proto kernel scope link src 192.168.7.2 linkdown

192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.185

? 此時 IP，路由,DNS 都有，那么就可以 ping 通外網

root@myir:~# ping www.baidu.com -I wlan0

PING www.a.shifen.com (163.177.151.109) from 192.168.43.185 wlan0: 56(84) byte

s of data. 64 bytes from 163.177.151.109 (163.177.151.109): icmp_seq=1 ttl=53 time=38.0 m

s

64 bytes from 163.177.151.109 (163.177.151.109): icmp_seq=2 ttl=53 time=127 m

s

^C

--- www.a.shifen.com ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4005ms

rtt min/avg/max/mdev = 38.038/78.559/126.632/34.542 ms

所以到這里可以得到即使 wifi 聯通還無法連通外網的原因，是需要對應的路由表。分析了網絡聯通的過程，那就可以使用 systemd-networkd 來進行多網絡管理。

5.4 systemd-networkd 增加 wlan0 管理

1) 在 /lib/systemd/network/中增加 79-wlan0.network 文件，并添加以下內容。

[Match]

Name=wlan0

[Network]

DHCP=yes

[DHCP]

RouteMetric=20

?RouteMetric 20 躍點數 20 （小于 eth0 的 15）

? 重啟 systemd-networkd 服務

root@myir:# systemctl restart systemd-networkd

? 查看 networkctl 狀態

root@myir:/lib/systemd/network# networkctl

IDX LINK TYPE OPERATIONAL SETUP

1 lo loopback carrier configured

2 can0 can off initialized

3 eth0 ether routable configured

4 wlan0 wlan routable configured

5 usb0 gadget no-carrier configuring

5 links listed. ?wlan0 現在變成 configured

接下來，重啟下系統，可以觀察到一個現象，就是 wifi 會自動打開，但是不會連接，那是因?yàn)闆]有 wpa_supplicant 服務，需要手動開啟。這樣才會將要連接 wifi 的SSID,PASSWD 和配置信息放置在/etc/wpa_supplicant.conf

手動開啟 wpa_supplicant 服務

root@myir:~# wpa_supplicant -B -iwlan0 -c /etc/wpa_supplicant.conf

ip route 信息

root@myir:~# ip route

default via 192.168.30.1 dev eth0 proto dhcp src 192.168.30.103 metric 15

default via 192.168.43.1 dev wlan0 proto dhcp src 192.168.43.186 metric 20

192.168.7.0/24 dev usb0 proto kernel scope link src 192.168.7.2 linkdown

192.168.30.0/24 dev eth0 proto kernel scope link src 192.168.30.103

192.168.30.1 dev eth0 proto dhcp scope link src 192.168.30.103 metric 15

192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.186

192.168.43.1 dev wlan0 proto dhcp scope link src 192.168.43.186 metric 20

? 這里可以看到 2 個 default，前面一個是 eth0 躍點數 15，后面 wlan0，躍點數 20。

此時就是以太網優先，如果以太網斷開，就走 WIFI 路由。測試 ping 百度不指定網

卡，中途拔掉以太網。

root@myir:~# ping www.baidu.com

PING www.a.shifen.com (163.177.151.110) 56(84) bytes of data. 64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=1 ttl=52 time=9.88 m

s

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=2 ttl=53 time=188 m

s

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=3 ttl=52 time=9.45 m

s

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=4 ttl=53 time=164 m

s

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=5 ttl=52 time=8.71 m

s

[ 190.316708] stm32-dwmac 5800a000.ethernet eth0: Link is Down

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=10 ttl=53 time=73.4

ms

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=11 ttl=53 time=71.6

ms

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=12 ttl=53 time=130

ms

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=13 ttl=53 time=68.8

ms

?[ 190.316708] stm32-dwmac 5800a000.ethernet eth0: Link is Down 拔掉網線

打印信息

可以看到以太網，wifi 同時連接時，網絡不會因?yàn)橐蕴W(wǎng)中斷而停止。這里還有一個點，到底 ping 的時候走那個網卡，這里直接說明，會走 ip route 最前面的 default 路由，由于 eth0 metric = 15 ，wifi metric=20，所以連接順序無論怎么接，都是以太網在前。

5.5 wpa_supplicant 自動啟動連接 wifi

上面章節雖然說明了 優先級情況，但是 wifi 需要手動啟動，無法自動連接，這里介紹如何開機啟動 wpa_supplicant。

前面章節有連接 wifi 時需要執行 wpa_supplicant 命令。

wpa_supplicant -B -iwlan0 -c /etc/wpa_supplicant.conf

? Wpa_supplicant 對應命令

? -B 后臺運行此程序

? -i wlan0 指定網卡名稱

? -c /etc/wpa_supplicant.conf 指定配置文件

其中/etc/wpa_supplicnat.conf 是需要寫入 SSID 與 passwd 的腳本

查看下使用 wpa_supplicant 服務的相關服務

root@myir:~# ls -l /lib/systemd/system/wpa_supplicant*

-rw-r--r-- 1 root root 453 Mar 9 2018 /lib/systemd/system/wpa_supplicant-nl802

11@.service

-rw-r--r-- 1 root root 447 Mar 9 2018 /lib/systemd/system/wpa_supplicant-wired

@.service

-rw-r--r-- 1 root root 245 Mar 9 2018 /lib/systemd/system/wpa_supplicant.servic

e

-rw-r--r-- 1 root root 415 Mar 9 2018 /lib/systemd/system/wpa_supplicant@.ser

vice

這里的 wpa_supplicnat@.service 是一個通配服務，試下執行命令

root@myir:~# systemctl enable wpa_supplicant@wlan0.service

Created symlink /etc/systemd/system/multi-user.target.wants/wpa_supplicant@wl

an0.service ->
/lib/systemd/system/wpa_supplicant@.service. 可以看到建立了一個開機啟動服務的軟連接到/etc/systemd/system/multi- user.target.wants/wpa_supplicant@wlan0.service

查看下自啟動軟連接信息。

root@myir:~# cat /etc/systemd/system/multi-user.target.wants/wpa_supplicant

@wlan0.service

[Unit]

Description=WPA supplicant daemon (interface-specific version)

Requires=sys-subsystem-net-devices-%i.device

After=sys-subsystem-net-devices-%i.device

Before=network.target

Wants=network.target

# NetworkManager users will probably want the dbus version instead. [Service]

Type=simple

ExecStart=/usr/sbin/wpa_supplicant -c/etc/wpa_supplicant/wpa_supplicant-%I.co

nf -i%I

[Install]

WantedBy=multi-user.target

?ExecStart=/usr/sbin/wpa_supplicant
-c/etc/wpa_supplicant/wpa_supplicant-%I.conf -i%I 這里我們將上面的生成的文件放置在/etc/wpa_supplicant/wpa_supplicant- wlan0.conf 不就可以自動啟動。 注意：MYD-YA15XC-T 的 wpa_supplicant.conf 在目錄/etc 下。需要按照自啟動的配置目錄，將 wpa_supplicant.conf 改成 wpa_supplicant-wlan0.conf 并拷貝到新建的目錄下

/etc/wpa_supplicant. root@myir:/etc/wpa_supplicant# ls

wpa_supplicant-wlan0.conf

重啟后可自動連接 wifi。

5.6 4G 模塊配置

從以上章節對 wifi 的配置來看，可以很快添加 4G 模塊的網絡，步驟如下：

?/lib/systemd/network/ 下添加 EC20 模塊的設備，設置成自動獲取 IP， metric。

?手動/自動連接模塊。

MYD-YA15XC-T 沒有直接的 4G 模塊的接口，需要通過 USB 轉 miniPCIe 的轉接板連接 4G 模塊。米爾默認移植的 4G 模塊為移遠 EC20；運營商測試為移動。

1) 啟動自動撥號腳本 quectel-CM &

root@myir:/etc/ppp# ./quectel-CM &

root@myir:/etc/ppp# [02-07_15:53:06:002] Quectel_QConnectManager_Linux_V1. 5.5

[02-07_15:53:06:004] Find /sys/bus/usb/devices/2-1 idVendor=0x2c7c idProduct=

0x125

[02-07_15:53:06:005] Auto find qmichannel = /dev/cdc-wdm0

[02-07_15:53:06:005] Auto find usbnet_adapter = wwan0

[02-07_15:53:06:005] Modem works in QMI mode

[02-07_15:53:06:043] cdc_wdm_fd = 7

[02-07_15:53:06:144] Get clientWDS = 18

[02-07_15:53:06:178] Get clientDMS = 1

[02-07_15:53:06:210] Get clientNAS = 3

[02-07_15:53:06:241] Get clientUIM = 1

[02-07_15:53:06:275] Get clientWDA = 1

[02-07_15:53:06:306] requestBaseBandVersion EC20CEFDKGR06A04M2G

[02-07_15:53:06:434] requestGetSIMStatus SIMStatus: SIM_READY

[02-07_15:53:06:466] requestGetProfile[1] ctnet///0

[02-07_15:53:06:498] requestRegistrationState2 MCC: 460, MNC: 0, PS: Attached, DataCap: LTE

[02-07_15:53:06:529] requestQueryDataCall IPv4ConnectionStatus: DISCONNECTE

D

[02-07_15:53:06:529] ifconfig wwan0 down

[02-07_15:53:06:547] ifconfig wwan0 0.0.0.0

[02-07_15:53:06:594] requestSetupDataCall WdsConnectionIPv4Handle: 0xe18a5fc

0

[02-07_15:53:06:722] ifconfig wwan0 up

[02-07_15:53:06:755] busybox udhcpc -f -n -q -t 5 -i wwan0

udhcpc: started, v1.31.1

udhcpc: sending discover

udhcpc: sending select for 10.38.63.3

udhcpc: lease of 10.38.63.3 obtained, lease time 7200

RTNETLINK answers: File exists

[02-07_15:53:07:222] /etc/udhcpc.d/50default: Adding DNS 120.196.165.7

[02-07_15:53:07:222] /etc/udhcpc.d/50default: Adding DNS 221.179.38.7

2) 查看 networkctl 狀態

LINK TYPE OPERATIONALSETUP

1 lo loopback carrier configured

2 can0 can off initialized

3 eth0 ether routable configured

4 wlan0 wlan routable configured

5 usb0 gadget no-carrier configuring

6 wwan0 wwan routable configured

6 links listed. 3) 再次重啟，eth0 和 wlan0 自動連接，執行 4G 的撥號腳本讓 EC20 撥號成功。

查看路由表：

root@myir:/etc/ppp# ip route

default via 10.75.115.24 dev wwan0 metric 10

default via 192.168.30.1 dev eth0 proto dhcp src 192.168.30.103 metric 15

default via 192.168.43.1 dev wlan0 proto dhcp src 192.168.43.185 metric 20

10.75.115.16/28 dev wwan0 proto kernel scope link src 10.75.115.23

192.168.7.0/24 dev usb0 proto kernel scope link src 192.168.7.2

192.168.30.0/24 dev eth0 proto kernel scope link src 192.168.30.103

192.168.30.1 dev eth0 proto dhcp scope link src 192.168.30.103 metric 15

192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.185

192.168.43.1 dev wlan0 proto dhcp scope link src 192.168.43.185 metric 20

4) Ping 外網的同時，下列做兩組測試。

? 第一組，依此拔下 EC20 模塊，拔下網線，關閉 wifi。

root@myir:/etc/ppp# ping www.baidu.com

PING www.a.shifen.com (163.177.151.110) 56(84) bytes of data. 64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=9 ttl=49 time=69.9 m

s

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=13 ttl=50 time=50.2

ms

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=14 ttl=50 time=55.2

ms

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=15 ttl=50 time=58.4

ms

[ 360.021410] usb 2-1: USB disconnect, device number 2

[ 360.025904] option1 ttyUSB0: GSM modem (1-port) converter now disconnecte

d from ttyUSB0

[ 360.034187] option 2-1:1.0: device disconnected

[ 360.039434] option1 ttyUSB1: GSM modem (1-port) converter now disconnecte

d from ttyUSB1

[ 360.046381] option 2-1:1.1: device disconnected

[ 360.059715] option1 ttyUSB2: GSM modem (1-port) converter now disconnecte

d from ttyUSB2

[ 360.066565] option 2-1:1.2: device disconnected

[ 360.094517] option1 ttyUSB3: GSM modem (1-port) converter now disconnecte

d from ttyUSB3

[ 360.114436] option 2-1:1.3: device disconnected

[ 360.127444] qmi_wwan_q 2-1:1.4 wwan0: unregister 'qmi_wwan_q' usb-5800d00

0.usbh-ehci-1, WWAN/QMI device

[02-07_15:56:39:842] QmiWwanThread poll err/hup/inval

[02-07_15:56:39:842] poll fd = 7, events = 0x0018

[02-07_15:56:39:842] QmiWwanThread exit

[02-07_15:56:39:845] ifconfig wwan0 down

ifconfig: SIOCGIFFLAGS: No such device

[02-07_15:56:39:957] ifconfig wwan0 0.0.0.0

ifconfig: SIOCSIFADDR: No such device

[02-07_15:56:40:053] qmi_main exit

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=17 ttl=52 time=10.0

ms

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=18 ttl=52 time=11.8

ms

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=19 ttl=52 time=10.7

ms

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=20 ttl=52 time=9.87

ms

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=28 ttl=52 time=9.82

ms

[ 373.447569] stm32-dwmac 5800a000.ethernet eth0: Link is Down

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=30 ttl=53 time=1573

ms

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=31 ttl=53 time=533

ms

64 bytes from 163.177.151.110 (163.177.151.110): icmp_seq=32 ttl=53 time=73.5

ms

ping: sendmsg: Network is unreachable

ping: sendmsg: Network is unreachable

ping: sendmsg: Network is unreachable

ping: sendmsg: Network is unreachable

^C

--- www.a.shifen.com ping statistics --- 39 packets transmitted, 37 received, 5.12821% packet loss, time 42301ms

rtt min/avg/max/mdev = 8.666/110.402/1572.819/261.269 ms, pipe 2

[1]+ Done ./quectel-CM

紅色字體分別是拔下 4G 模塊與拔下以太網的信息再斷下 wifi(由于斷 wifi 無消息顯示)，打印消息上看，網絡并沒有斷掉。

? 第二組，分別斷掉 wifi, 以太網，4G 模塊。

root@myir:/etc/ppp# ping www.baidu.com

PING www.a.shifen.com (183.232.231.174) 56(84) bytes of data. 64 bytes from 183.232.231.174 (183.232.231.174): icmp_seq=1 ttl=56 time=49.6 m

s

64 bytes from 183.232.231.174 (183.232.231.174): icmp_seq=21 ttl=56 time=45.7

ms

64 bytes from 183.232.231.174 (183.232.231.174): icmp_seq=22 ttl=56 time=48.8

ms

64 bytes from 183.232.231.174 (183.232.231.174): icmp_seq=23 ttl=56 time=47.8

ms

64 bytes from 183.232.231.174 (183.232.231.174): icmp_seq=24 ttl=56 time=47.7

ms

[ 248.247712] stm32-dwmac 5800a000.ethernet eth0: Link is Down

64 bytes from 183.232.231.174 (183.232.231.174): icmp_seq=25 ttl=56 time=46.6

ms

64 bytes from 183.232.231.174 (183.232.231.174): icmp_seq=29 ttl=56 time=134

ms

64 bytes from 183.232.231.174 (183.232.231.174): icmp_seq=30 ttl=56 time=394

ms

64 bytes from 183.232.231.174 (183.232.231.174): icmp_seq=31 ttl=56 time=88.2

ms

[ 255.315629] usb 2-1: USB disconnect, device number 2

[ 255.320113] option1 ttyUSB0: GSM modem (1-port) converter now disconnecte

d from ttyUSB0

[ 255.342216] option 2-1:1.0: device disconnected

[ 255.349262] option1 ttyUSB1: GSM modem (1-port) converter now disconnecte

d from ttyUSB1

[ 255.356317] option 2-1:1.1: device disconnected

[ 255.376938] option1 ttyUSB2: GSM modem (1-port) converter now disconnecte

d from ttyUSB2

[ 255.394263] option 2-1:1.2: device disconnected

[ 255.417228] option1 ttyUSB3: GSM modem (1-port) converter now disconnecte

d from ttyUSB3

[ 255.442233] option 2-1:1.3: device disconnected

[ 255.462782] qmi_wwan_q 2-1:1.4 wwan0: unregister 'qmi_wwan_q' usb-5800d00

0.usbh-ehci-1, WWAN/QMI device

[02-07_15:54:56:702] QmiWwanThread poll err/hup/inval

[02-07_15:54:56:702] poll fd = 7, events = 0x0018

[02-07_15:54:56:703] QmiWwanThread exit

[02-07_15:54:56:705] ifconfig wwan0 down

ifconfig: SIOCGIFFLAGS: No such device

[02-07_15:54:56:798] ifconfig wwan0 0.0.0.0

ifconfig: SIOCSIFADDR: No such device

[02-07_15:54:56:819] qmi_main exit

ping: sendmsg: Network is unreachable

ping: sendmsg: Network is unreachable

ping: sendmsg: Network is unreachable

ping: sendmsg: Network is unreachable

^C

--- www.a.shifen.com ping statistics --- 39 packets transmitted, 31 received, 20.5128% packet loss, time 38340ms

rtt min/avg/max/mdev = 37.010/65.549/393.764/63.096 ms

[1]+ Done ./quectel-CM

root@myir:/etc/ppp#

可以看到最后斷下 4G 模塊后才斷掉網絡。

審核編輯：符乾江