SS524V100 SDK安裝編譯osdrv注意事項（一）

一、開發環境

windows10電腦 +虛擬機15 Pro + Ubuntu18.0.4

二、在 linux服務器上安裝交叉工具鏈

1# tar -zxf arm-mix410-linux.tgz

2# cd armmix410-linux

3# chmod +x arm-mix410-linux.install

4# sudo .armmix410-linux.install opthisi-linuxx86-arm 指定安裝路徑：opthisi-linuxx86-arm，如果不帶這個參數默認安裝路徑為：optlinuxx86-arm

5# source etcprofile 安裝交叉編譯器的腳本配置的環境變量就可以生效了，或者請重啟linux服務器也可

三、安裝 SDK

3.1 SS524V100 SDK包位置

1.原始包： SS524V100R00101.softwareboardSS524V100_SDK_V2.0.X.X.tgz

2.補丁包： SS524V100R00102.only for referencesoftwareboardSS524V100_REF_V2.0.X.X.tgz

3.補丁腳本： SS524V100R00102.only for referencesoftwareboardref_patch.sh

3.2解壓縮并展開 SDK包

SS524V100_REF_V2.0.X.X.tgz作為補丁包，可以將此補丁包打到SS524V100_SDK_V2.0.X.X.tgz包中，具體操作步驟如下：

1# 1、將 SS524V100_SDK_V2.0.X.X.tgz和 SS524V100_REF_V2.0.X.X.tgz 包放置到同一個文件夾下并解壓

2# tar -zxf SS524V100_SDK_V2.0.X.X.tgz

3# tar -zxf SS524V100_REF_V2.0.X.X.tgz

4

5# 2、執行 SS524V100_SDK_V2.0.X.X文件夾內部解壓

6# cd SS524V100_SDK_V2.0.X.X

7# .sdk.unpack

8

9# 3、執行打補丁操作：

10# cd ..

11# chmod +x ref_patch.sh

12# .ref_patch.sh

執行后，SS524V100_SDK_V2.0.X.X為打上REF補丁后的完整包。

四、編譯 osdrv

本目錄下的編譯腳本支持 arm-mix410-linux工具鏈，arm-mix410-linux對應glibc庫。具體命令如下(以ss524v100舉例)：

4.1徹底清除整個osdrv目錄

# cd SS524V100_SDK_V2.0.1.0osdrv

# make distclean

4.2編譯整個osdrv目錄

# make all

五、編譯問題匯總及解決方法

5.1問題1

binsh 1 bison not found

解決方法

# sudo apt install bison flex

5.2問題2

configure error gperf not found

Makefile10 recipe for target ‘a(chǎn)ll’ failed

make[1][all] Error 1

make[1]離開目錄“SS524V100_SDK_V2.0.1.0open_sourceeudev”

Makefile330 recipe for target ‘boardtools’ failed

make[boardtools] Error 2

解決方法

# sudo apt-get install gperf

5.3問題3

configure WARNING cannot find ZLIB library required for mkfs programs

configure mtd-utils can optionally be built without mkfs.ubifs

configure mtd-utils can optionally be built without mkfs.jffs2

configure error missing one or more dependencies

Makefile47 recipe for target ‘mtd_board’ failed

make[1][mtd_board] Error 1

make[1]離開目錄“SS524V100_SDK_V2.0.1.0open_sourcemtd-utils”

Makefile330 recipe for target ‘boardtools’ failed

make[boardtools] Error 2

解決方法

安裝 mtd-utils2.x.x依賴庫：

# sudo apt-get install zlib1g-dev liblzo2-dev uuid-dev pkg-config automake

5.4問題4

7z x lzma1900.7z -olzma1900

make[1] 7z Command not found

Makefile7 recipe for target ‘a(chǎn)ll’ failed

make[1][all] Error 127

make[1]離開目錄“SS524V100_SDK_V2.0.1.0open_sourcelzma”

Makefile291 recipe for target ‘pctools’ failed

make[pctools] Error 2

解決方法

# sudo apt install p7zip-full

1

---------finish osdrv work，表示整個osdrv編譯成功了

————————————————